How to Install Wall and Ceiling Mouldings

Wall and ceiling mouldings give a room a finished look and hide small imperfections where the wall meets the ceiling. The mouldings in our range (by Mardom Decor) are made from PolyForce, a dense polymer that is unaffected by moisture and won't turn yellow in sunlight. Fitting them isn't difficult, but a great result comes down to three things: accurate cuts, the right adhesive and careful finishing.

Before you start

  • Leave the mouldings in the room where they'll be fitted for at least 24 hours so the material can adjust to the temperature and humidity.
  • Check them for any transit damage.
  • The surface must be dry, clean, dust-free and even. Remove any flaking paint and fill larger imperfections.
  • Mark the position of the moulding with a line laser and a pencil. For a cornice, mark a line on both the wall and the ceiling.

Tools

A professional finish needs professional tools. We recommend a mitre saw for cutting the corners. A wooden mitre box and a hand saw won't give you an accurate enough angle, and the corner joints will show.

The right saw blade is the key to success. Use a fine-tooth blade designed for cutting plastics and laminate, for example a 250 mm blade with at least 80 teeth. A coarse blade tears the edges of the polymer and leaves a ragged cut. Let the blade reach full speed and guide it through the moulding smoothly, without forcing it.

You'll also need a tape measure, a pencil, a line laser, a caulking gun, a filling knife, fine sandpaper or a sanding sponge, a damp cloth and masking tape.

Three adhesives and what each one is for

  • Mardom Fix Pro is a mounting adhesive for fixing mouldings to walls and ceilings indoors. It works on plaster, plasterboard, wood and concrete, has no odour and contains no solvents.
  • Mardom Fix Extra is a joint adhesive. It bonds the ends of the mouldings together and fills the gap between them, so the joint won't crack or show through the paint.
  • Mardom Fix Max is a strong hybrid adhesive with almost instant grab. Use it for heavier and wider profiles, smooth or low-absorbency surfaces (such as gloss paint or tiles) and in damp rooms. Fix Max can also be used outdoors.

Step by step

  1. Start with the corners. Measure the moulding and cut the ends for internal and external corners at 45°. Before the first real cut, try a test piece and check the angle against the wall.
  2. Apply mounting adhesive (Fix Pro or Fix Max) to the sides of the moulding that will sit against the wall and ceiling, in a continuous bead or closely spaced dots.
  3. Apply Fix Extra joint adhesive to the whole cut face at every joint. A joint without adhesive will crack over time.
  4. Press the moulding onto the marked line and hold it for a moment. Support longer lengths with masking tape until the adhesive grabs.
  5. Wipe away any excess adhesive straight away with a damp cloth.
  6. Leave the adhesive to dry for at least 24 hours.
  7. Fill any gap between the moulding and the wall with acrylic caulk and fill the joints with Mardom Decor filler. Once the filler is dry, sand it smooth with fine sandpaper.

Painting

The mouldings come factory-primed, so you can paint them as soon as the adhesive has dried.

  • Use a water-based acrylic paint. Solvent-based paints can damage the surface of the moulding.
  • Apply two thin coats with a brush or a small foam roller. A paint sprayer gives the smoothest finish.
  • If the moulding is going to be the same colour as the wall, paint them together so the line between them disappears.
  • For a contrasting colour, mask the wall along the moulding and remove the tape while the paint is still wet.
  • Paint flexible (Flex) mouldings only after they have been glued in place.

Tips

  • Plan the joints so they are as discreet as possible, for example behind furniture or above a door.
  • If the wall or ceiling isn't straight, don't force the moulding against it. Fill the gap with caulk afterwards.
  • You'll find mouldings, adhesives and filler in the Wall Mouldings and Adhesive/Accessories sections of our online shop. If you're not sure which adhesive to choose, just ask us in the showroom.